Risco ProSound RS200WA0000B 100dBA outdoor siren with double self-protected protection in metal and UV polycarbonate housing, with long-life SLT flashing light and up to 36 hours autonomy. Maximum tamper protection.
Powerful 100dBA loudspeaker at 3 meters.
High-efficiency long-life SLT beacon
Double mechanical protection: metal shell + UV polycarbonate
Autonomy: 36 hours in stand-by or 80 min in alarm
Tamper anti-opening, anti-removal
Inputs protected against reverse polarity and overvoltage
Can be used on ProSYS BUS or as a conventional siren
This siren has the same features as model RS200WAP000B but without Anti-foam protection and Anti-approach detection.
Politiche per la sicurezza
(modificale nel modulo Rassicurazioni cliente)
Politiche per le spedizioni
(modificale nel modulo Rassicurazioni cliente)
Politiche per i resi
(modificale nel modulo Rassicurazioni cliente)
The Risco ProSound RS200WA0000B outdoor siren is designed to provide total protection thanks to its dual mechanical structure: a metal inner container combined with a UV-treated polycarbonate shell that is weatherproof and vandal-resistant.
The SLT (Smart Light Technology) beacon provides long life and visibility in all weather conditions. Built-in status LED provides indication of system on/off.
Compatible with systems on ProSYS BUS and conventional installations, the siren features inputs for positive and negative commands, electronic protection against reverse polarity and overvoltage, and intelligent battery management with automatic disconnection to prevent deep discharge.
Equipped with mechanical tamper and active protections, the siren provides long autonomy:
Up to 36 hours standby time
Up to 80 minutes of continuous alarm
Long-lasting SLT flasher combined with the 100+ dBA siren
Vandal-resistant polycarbonate housing with UV treatment
Internal metal enclosure for double mechanical protection
Unique remote control and diagnostic capabilities
Power inputs protected against reverse polarity, interference and overvoltage
Positive and negative alarm control inputs
Automatically recharging battery circuit
Automatic battery disconnection to prevent complete battery discharge
Battery life of 36 hours in backup or 80 minutes in alarm
Tamper-resistant devices for opening and removal with built-in EOL resistors
Indications via system status LEDs for arming/disarming and alarm memory
Remote analog readout of power input voltage
Measurement of charging current
Remote measurement of battery backup voltage level
Speaker absorption level (when activated)
Activation of dynamic battery test by dummy load
Programming of flasher blinking frequency (20 to 60 times per minute)
| Feature | Detail |
|---|---|
| Power input | 13.5 to 14.2 VDC, 200mA maximum |
| Quiescent current consumption | 54mA + battery current recharge |
| Current consumption in alarm (Siren + Flashing) | 1A nominal (1.6A maximum) |
| Speaker sound level | Over 100 dBA at 3 meters |
| Acoustic tone frequency | 1500-1800 Hz |
| Flasher | Surface Light Technology SLT™ with 6000 mcd |
| Flasher plastic | Polycarbonate |
| Flashing Intermittence | Up to 60 times per minute |
| Battery back-up | SLA rechargeable, 12V, 2.2 Ah (178 x 64 x 35 mm) |
| Battery discharge protection | Automatic disconnection below 10.5 VDC |
| Degree of protection | IP43 |
| Operating temperature range | -25ºC to 70ºC |
| Humidity | 95% maximum |
| Tamper contacts | 0.5A, 24V, NC or EOL termination with integrated resistor |
| Outer case material | Polycarbonate with UV protective treatment |
| Dimensions (H x W x D) | 305 x 218 x 116 mm |
| Compatibility | All control panels |
| Bus compatibility | Connection via 4-wire RS485 bus |
check_circle
check_circle
Comments (0)
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent