Bticino Video Intercom Kit CLASSE100 V16E 2-Wire Single-Family 364612

Technical specifications of kit parts:


 

1 LINEA 3000 video handset code 343081:

• 2-wire technology
• Wall-mounted installation with zamak front panel and wide-angle color camera
• White LEDs for illuminating the camera field in low light conditions
• Configurable for single-family or two-family installations
• Allows activation of an electric lock connected directly between terminals S+ and S- (18 V 4 A impulsive, 250 mA hold, 30 Ohm max)
• Illumination of the name tag with white LEDs
• Meets IP54 degree of protection - IK10 strength rating.

• Dimensions: 190x100x26.65mm
• Height: 190mm
• Width: 100mm
• Depth: 26.65mm
• Calls: 2
• Installation type: 2 wire
• Recommended installation height: 160-165cm
• Operating temperature: -25/+70°C
• Resolution: 330 TV Lines H / 330 TV Lines H
  
  
   

1 Video Intercom CLASSE 100V16E code 344672:

• 2-wire handsfree technology, with teleloop
• 5" color LCD display
• Has 2 physical buttons for controlling the main video door phone functions - call answering and closing - has 3 touch buttons for controlling the main functions - electric lock activation, staircase light control and door station/loop activation - plus an additional 4 configurable touch buttons that take on different functions - e.g., intercom, additional electric lock activation, general activations
• The video intercom has a side toggle for adjusting : color, display brightness and contrast, speech volume and call tone volume
• There is a signaling LED for call mute
• Installation can be done off the wall with special bracket (supplied) or via table stand (to be purchased separately code 344692)
• The device, which also has a professional studio function, must be configured.

• Voltage: 20/27V
• Dimensions: 165x164x20.5mm
• Height: 165mm
• Width: 164mm
• Depth: 20.5mm
• Maximum cable cross section: 2x1mmq
• Installation type: 2 wires
• Recommended installation height: 160-165cm
• Operating temperature: -5/+40°C
• Resolution: 800 x 480
• Wi-Fi: No
• Teleloop: Yes
• Color: White
  
   

1 BUS-SCS power supply in 6 DIN modular housing for 2-wire audio and video systems code 346050:

• Power supply for 2-wire audio and video systems in 6 DIN modular housing
• Power supply 110 - 240 Va.c. @ 50 - 60 Hz
• Provides two safety extra-low voltage supplies at the output (one on the 3 terminals BUS TK, BUS PI and SCS, one on terminal 1 - 2);
• To be used alternately and Not simultaneously
• The video adapter is built into the device (item 346830 should therefore not be used), so it is possible to avoid the use of the A/V node (F441) or multi-channel matrix (F441M) if from the BUS PI and BUS TK terminals a total of three leads are not exceeded (MAX 2 PI risers + 1 TK or 1 PI riser + MAX 2 TK)
• It can also be used as an additional power supply (output 1 - 2) for local power supply of indoor stations or prearranged outdoor stations (in this case, no other output can be used)
• The device is electronically protected against overload and short circuit
• It is a double-insulated SELV safety device
• Installation must be carried out in accordance with current regulatory rules
• The device must NOT be configured
• Attention: the outputs (BUS PI), (BUS TK) and (SCS) can be used at the same time while respecting the maximum total power consumption of 1.2 A
• After overload or a short circuit, disconnect the power supply for 5 minutes
• This power supply is CAT II 2500 V category, so it needs additional protection from transient voltages (higher than the design overvoltage category) external to the equipment
• The power supply must be installed only in switchboards designed for DIN luminaires
• Must only be installed indoors
• An omnipolar switch with contact separation of at least 3 mm must be used, located in the vicinity of the power supply unit
• The switch described above is to be considered as a device for disconnecting the power supply unit from the mains supply
• Do not solder the end of the conductors that are inserted into the terminals. Overall dimensions: 6 DIN modules

PRI (AC power input):

• Rated voltages: 110 - 240V
• Rated currents: 730 - 400 mA
• Working frequency range: 50 - 60 Hz
• Power consumption at full load: 40 W max
• Power dissipation: 8 W max
• Efficiency at full load: 80 % typ
• Stand-by power: < 1W
• Operating temperature: (-10) - (+55) °C
• Integrated fuse (PRI side): F1 T 3.15A 250 V
  
  
   

BUS TK, BUS PI, SCS:

• Rated voltage: 27 Vdc
• Rated current: 1.2 A
• Rated power: 32.4 W
  
  
   

1-2:

• Rated voltage: 28.5 Vdc
• Rated current: 1.2 A
• Rated power: 34.2 W
  
   

Power supply installation:

• The power supply unit must always be installed in appropriate enclosures.
• Must not be exposed to dripping or splashing water
• Do not obstruct ventilation openings
• A double-pole switch with contact separation of at least 3 mm must be used, placed near the power supply. The switch has the dual purpose of being able to disconnect the power supply from the mains and to protect the power supply.
  
  
   

1 relay module for electromechanical locks not managed by BUS (code 346250): Relay module for gate opening to be combined with prearranged external pushbuttons. Allows opening of locks NOT operated by BUS via the door station. Contact type: NO-NC, system type: 2 wires.